Motorized Probe Heads

Showing 1–12 of 65 results

Active filters
Clear Filters

The AM1 adjustment module is designed for use with the PH10T and PH10M probe heads. Each module provides quick and accurate angular alignment of the motorized probe head with the CMM’s axes and/or the autochange rack. The quick release mechanism allows the head to be removed for storage and replaced without further alignment.

Size 60 mm x 15.5 mm
Adjustment ±2° in pitch and roll*
±4.5° in yaw
Overtravel ±3.5° in pitch and roll
Mounting Mounts to quill using shank
*Up to ±5.5° in pitch and roll is possible, but at the expense of overtravel.

The AM2 is designed for the PH10MQ probe heads. Each module provides quick and accurate angular alignment of the motorized probe head with the CMM’s axes and/or the autochange rack. The quick release mechanism allows the head to be removed for storage and replaced without further alignment.

Size 80 mm x 10 mm
Adjustment ±1° in pitch and roll*
±1° in yaw
Overtravel 0
Mounting Mounts direct to quill

*Up to ±5.5° in pitch and roll is possible, but at the expense of overtravel.

The HCU2 hand control unit enables the probe head to be used in a manual mode or during a teach cycle. An LCD dot matrix display provides information and status of the PHC10-3 system.

  • Basic low cost joystick for 3-axis CMM without an LCD
  • Compatible with the range of Renishaw CMM controllers and incorporates all the functionality of the HCU2 hand controller for motorised head
  • Basic low cost joystick for 3-axis CMM without an LCD
  • Controls motion of CMM axes
  • Indexes the motorised head and rotary table
  • Has a system menu for navigating the operating software
  • Handheld or table mounted operation
  • The wireless manual control unit (MCU W-2) is a comprehensive joystick designed for use with Renishaw’s range of UCC controllers
  • Based on the MCU5-2 joystick design, the MCU W-2 uses modern battery technology and Bluetooth® radio modules to provide an effective wireless joystick with a maximum of 25 m range and over eight hours between battery changes
  • A spare battery and an automatic charger are included in the joystick docking cradle
  • The manual control unit is a comprehensive CMM joystick controller designed for use with Renishaw’s range of UCC controllers
  • It includes the functionality of both the Renishaw standard UCC joystick interface and Renishaw PHC10 hand control unit (HCU2)
  • The MCU5-2 is a development of the MCU5 joystick, with new buttons and new functionality
  • The MCU5-2 has been developed for use with Renishaw’s REVO system and PH20, providing the ability to move the CMM in the axis of the probe and stylus

The PH10M PLUS motorized probe head has been developed for the new generation of contact and non-contact scanning probes. It has three times the torque of PH10 PLUS, allowing probe extension bars up to 300 mm long to be used.
The PH10M PLUS has an autojoint mounting.

PH10M-iQ PLUS functions identically to a traditional PH10M PLUS but with the addition of inferred qualification technology. Inferred qualification increases throughput by removing the need to qualify each head position that is used in a measurement program.

PH10M-iQ PLUS works with all PH10M compatible probes, but only touch-trigger probe configurations can utilize inferred qualification. Scanning probes can be used in traditional PH10M qualification mode but cannot use inferred qualification.

The PH10MQ PLUS can be mounted vertically inside the CMM’s quill for a greater working envelope by increasing the Z axis travel. The specification of the PH10MQ PLUS is identical to that of the PH10M PLUS, with the following exceptions:

Head mounting: Direct to quill
Dimensions: Length 73 mm, width 80 mm
Weight: 730 g
Part number: A-5863-6000

The new PH10T PLUS motorized probe head allows complete, rapid, and repeatable inspection of most complex components with minimum human intervention. Full orientation of your TP2, TP6, TP20 or TP200 probe between any of 720 positions, under manual or program control, turns your 3 axis CMM into a 5 axis machine.