Metric

Showing 1–12 of 151 results

Active filters
Clear Filters

Fast and accurate method of thread measuring available for use with Micrometer

Specially designed to measure the distance between two centers or the distance from an edge to center.
Provided with jaws on the back of the slider, measurements can be read easily by looking down.
Direct reading of pitch measurements is available due to the offset value setting function.
With SPC data output.
Supplied fitted in wooden case.

Can be used in workshop conditions exposed to coolant, water, dust or oil.
Easy to use – no need to wipe or clean the scale.
Advanced design styling.
Incorporates absolute measurement system.
Automatic power-on/off.
Data output function.
With thumb roller.
Supplied in fitted plastic case.

Designed with a back plunger type dial indicator for upward facing readings. (7231, 7237T, 7238T)

•The rounded faces of the jaws are ideal for accurate ID (inside diameter) measurement.
•Inside and outside measurements can be directly read from the upper and lower slider graduations (Series 160).
•With fine-adjustment carriage type is available (Series 160).
•Parallax-free vernier scale type is available for easy and positive measurement (Series 160).
•With SPC output (Series 550).
•Supplied in fitted plastic case. Except 1000mm / 40” supplied in wooden case.

Mitutoyo’s absolute Digimatic Caliper is the next generation of electronic calipers. It keeps track of its origin point once set. Whenever turned on, the large LCD displays the actual slider position ready to start measurement. No more repeated zero setting is necessary with the absolute encoder technology, as well as no more concern for over speed errors.

Large and clear LCD readout.
The ZERO/ABS key allows the display to be Zero-Set at any slider position along the scale for incremental comparison measurements. This switch will also allow return to the absolute (ABS) coordinate and display of the true position from the origin point (usually jaws-closed point).
Data Hold Unit (959143) is optional.
Carbide-tipped jaw type calipers are also available.
With thumb roller. Except 500-500-10, 500-501-10,500-502-10.
Supplied in fitted plastic case. Except 1000mm / 40” supplied in wooden case.

The rounded faces of the jaws are ideal for accurate ID (inside diameter) measurement.
With SPC output.
Supplied in fitted plastic holster in carton.18″/450mm and larger supplied wooden case.

‘- ABSOLUTE Digimatic Depth Gage can keep track of the origin point once set for the entire life of the battery.
– Wide probing range is available with the supplied extension rod.
– Bottom surface of the base is hardened, ground and lapped for highest degree of flatness.
– With SPC data output.

Built-in ABSOLUTE linear encoder this encoder eliminates the necessity of setting the reference point at every poweron. It has improved reliability because no over-speed error will occur.
Fine-adjustment carriage for smooth movement.
Carbide-tipped scriber is provided.
With SPC data output.

Built in ABSOLUTE linear encoder.
This encoder eliminates the necessity of setting the reference point at every power-on. It has improved reliability because no over-speed error will occur.
Rigid column structure ensures high measuring accuracy.
With large smooth slider feed wheel.
Carbide-tipped scriber is provided.
With SPC data output.

The new Calculation-Type Digimatic Indicator features both a Key- Lock and Parameter-Lock to prevent accidental changing of settings during operation.
Improved parameter setting software makes easy to set all available parameters, and determine and upload the proper coefficients for calculation. (optional)
Fast measurement frequency allows the user to increase the number of readings per second from 10 to 50, allowing higher accuracy measurements of TIR and MAX/MIN.
An analog bar provides easy-to-read values when scanning for Max, Min, and TIR Values.
The Absolute Digimatic indicator performs internal calculations using the formula Ax+B+Cx-1 (assuming spindle displacement as x) while the specified coefficients A, B and C can be set with respect to the purpose of measurement or dimensions of the fixtures. This unique features allows you to read your measurements directly, without the need for conversions.

The new Bore Gage-Type Digimatic Indicator features both a Key-Lock and Parameter-Lock to prevent accidental changing of settings during operation.
Parameter setting software makes it easy to set all available parameters. (optional)
Fast measurement frequency allows the user to increase the number of readings per second from 10 to 50.
The minimum value holding function provides the easy detection of hole diameter.
An analog bar indicator is integrated to enhance the intuition in reading.
Go/no-go judgment is performed by setting the upper and lower tolerances.
Up to three sets of master values and upper/lower tolerance values can be memorized.
Employing the ABSOLUTE linear encoder, the ID-C always displays the spindle Absolute Position from the origin when turned on.